色无五月,国产成人综合日韩精品婷婷九月,激情五月五月婷婷,精品免费看,99国产精品免费观看视频,国产亚洲精品成人婷婷久久小说

Installation method of intelligent electromagnetic flowmeter

  • KEWILL
  • 2022-07-21 18:19:33
  • 0time

The intelligent electromagnetic flowmeter is an electromagnetic induction flowmeter, which consists of sensors and intelligent signal converters. It can measure the volume flow of various conductive liquids, the measured media include strong corrosive liquids such as acid, alkali, salt, raw water, cooling water and other conductive liquids and solid-liquid two-phase liquids.

In order to ensure the measurement accuracy of the electromagnetic flowmeter, please observe the following points during installation:

1: The transmitter should be installed in a ventilated and dry place. Avoid installing it in a place where the ambient temperature is too high, and try to avoid equipment with strong magnetic fields, such as large motors, transformers, etc. Avoid installing it in places with corrosive gases. Installation location To facilitate maintenance.

2: In order to ensure that the measuring tube of the transmitter is filled with the measured medium, it is best to install the variable transformer vertically with the flow direction from bottom to top. Especially for liquid-solid two-phase flow, it must be installed vertically. If only horizontal installation is allowed on site, it must be installed vertically. Make sure the two electrodes are at the same level

3: In order to avoid the influence of the relative measurement of the flow rate, the flow control valve should be set downstream of the transmitter. For small-diameter transmitters, the distance from the center of the electrode to the inlet end of the flowmeter is equivalent to several times the diameter D. Therefore, there is no requirement for the upstream straight pipe. However, for a flowmeter with a larger diameter, there should generally be a straight pipe section above 5D in the upstream, and generally no straight pipe section is required in the downstream.

4: Valves and bypasses should be installed at both ends of the transmitter.

5: The AC potential of several millivolts measured by the electrode of the electromagnetic flow transmitter is based on the liquid potential in the transmitter. In order to stabilize the liquid potential and keep the transmitter and the fluid at the same potential to ensure stability The transmitter casing and both ends of the metal pipe should be well grounded, and the converter casing should also be grounded. The grounding resistance should not be greater than 10, and it should not be shared with the grounding wire of other electrical equipment. If the transmitter housing cannot be guaranteed to be in good contact with the metal pipes, use metal wires to connect them. Then ground them reliably.

6: The installation site of the converter should avoid strong AC and DC magnetic fields and vibration, the ambient temperature is -20 to 50 °C, does not contain corrosive gases, and the relative humidity is not greater than 80%.

7: In order to avoid interfering signals, the signal between the transmitter and the converter must be transmitted with shielded wires. It is not allowed to put the signal cable and the power cable in parallel in the same cable steel pipe. The length of the signal cable should not exceed 30m in general

主站蜘蛛池模板: 免费看毛片的网址 | 99视频在线看| 黄视频网站入口 | 国产精品免费小视频 | 亚洲国产精品久久久久 | 激情中文网 | 99精品免费视频 | 国产免费久久精品99久久 | 亚洲高清在线天堂精品 | 可以免费看的毛片 | 美女福利视频网站 | 国产精品亚洲片在线牛牛影视 | 毛片在线视频 | 国产精品视频一区二区三区w | 99久久999久久久综合精品涩 | 精品国产成人综合久久小说 | 天天综合久久久网 | 福利入口在线观看 | 给我们免费播放片 | 久久亚洲精品成人综合 | 九九精品视频在线 | 91久久精品国产91性色tv | 国产高清在线精品一区 | 国产精品视频一区二区三区 | 九九精品久久久久久噜噜中文 | 国产一区二区三区不卡免费观看 | 色婷婷六月桃花综合影院 | 国产欧美一级片 | 毛片久久 | 五月婷婷色视频 | 伊人草久久 | 一级毛片免费视频 | 久久这里只精品 | 久在草在线 | 草草福利影院 | 婷婷开心色 | 国产精品欧美亚洲韩国日本不卡 | 欧美国产成人精品一区二区三区 | 开心激情网五月天 | 久久精品日日躁夜夜躁欧美 | 精品久久国产视频 |