色无五月,国产成人综合日韩精品婷婷九月,激情五月五月婷婷,精品免费看,99国产精品免费观看视频,国产亚洲精品成人婷婷久久小说

Introduction

Principle & Structure

Turbine flowmeters are a type of velocity flowmeter. As shown in the figure below, a turbine is placed in the center of the pipeline, and the two ends are supported by bearings. When the fluid passes through the pipeline, it impacts the turbine blades and generates a driving torque for the turbine, so that the turbine can overcome the friction torque and fluid resistance torque to generate rotation. Within a certain flow range, for a certain viscosity of the fluid medium, the rotational angular velocity of the turbine is proportional to the fluid flow rate. Therefore, the fluid flow rate can be obtained from the rotational angular velocity of the turbine, so that the fluid flow through the pipeline can be calculated.

The rotational speed of the turbine is detected by a sensor coil mounted outside the casing. When the turbine blade cuts through the magnetic field lines created by the permanent magnet steel in the casing, it causes a change in the magnetic flux in the sensing coil. The sensing coil sends the detected magnetic flux periodic change signal to the preamplifier, amplifies and shapes the signal, generates a pulse signal proportional to the flow rate, and sends it to the unit conversion and flow accumulation circuit to obtain and display the cumulative flow value; At the same time, the pulse signal is also sent to the frequency-current conversion circuit, and the pulse signal is converted into an analog current, thereby indicating the instantaneous flow value.

main feature

● Installed with high-reliability long-life bearings

● Excellent repeatability, suitable for batching

● Excellent low flow rate measurement performance

● Extremely fast response, suitable for batch control and proportioning control applications

● Rotor with multi-blade structure, high precision

● Steam cleaning allowed

● The compact type is suitable for equipment installation

application

● Refined oil, light crude oil, gasoline, light oil, jet fuel, light diesel oil, naphtha, ethylene, etc.

● Lubricating oil, hydraulic oil, etc.

● Water, pure water, distilled water, deionized water, desalinated water, demineralized water, etc.

● Alcohol, benzene, toluene, xylene, butadiene, carbon tetrachloride, methylamine, acrylonitrile, etc.

● Formaldehyde, acid, caustic soda, carbon disulfide, etc.

● Milk, coffee, etc.

● High temperature medium such as heat transfer oil and hot kerosene

technical parameter

Accuracy:0.5% of rate and 0.2% of rate
Repeatability:±0.1% of measured value
Response time:50 ms max relative to input change
stability:Stability over 6 months is ±0.1% of measured value
Influence of ambient temperature:Over the operating temperature range is ±0.25% of the measured value
Influence of installation location:It is necessary to ensure that the sensor is full of pipes and to ensure that there are enough straight pipe sections before and after, then the installation has no effect
Start Time:50ms from zero traffic
Preheat time:5 minutes from power-on to rated measurement accuracy
Sensor parameters
size:DN4 to DN250
Measured fluid temperature range:-40 to 120°C; (>120°C and ≤180°C customized type can contact sales engineer)
Sensor body material:Stainless steel 1.4301 (304), stainless steel 1.4435 (316L), Hastelloy C
Impeller and accessories material:430F stainless steel, stainless steel 1.4435 (316L), Hastelloy C
Ball bearing material:316L SST bearing or ceramic bearing
Process connection:PN10 to PN63
Coil Impedance:1600Ω
Junction box parameters
Ambient temperature range:-20 to 140° F (-29 to 60 ℃ )
Junction box material:Stainless steel 1.4301 (304), IEC60529 IP66 (standard), can be customized stainless steel 1.4435 (316L)
Converter seal:rubber
power supply:DC 12V to 30V, 1A fast fuse fuse;
Protection class:IP65&IP67
Electrical Interface:PG13.5
power:max 0.3 w
output:Pulse output (for total)

Selection table

FR60-Turbine Flowmeter

The way to

DN4 DN6 DN10 DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 DN125 DN150 DN200 DN250

output signal

pulse

0-5V

4-20mA

4-20mA+pulse+2 switch output

4-20mA+pulse+2-way switch output+instantaneous flow display+cumulative flow display

Process connection type

Threaded seal connection

Flange connection

Sanitary clamp connection

precision


Accuracy 0.2% (suitable for pipelines above DN ≥ DN15)

Accuracy 0.5%

Accuracy 1.0%

Wiring

Stainless steel 1.4301 (304) junction box IP67

Aviation socket connector IP65

Hessman joint (DIN43650) IP65

Pressure rating

EN 1092-1 (DIN) PN10
ASME B16.5(ANSI)CLASS150

EN 1092-1 (DIN) PN16
ASME B16.5(ANSI)CLASS300

EN 1092-1 (DIN) PN25
ASME B16.5(ANSI)CLASS600

EN 1092-1 (DIN) PN40
ASME B16.5(ANSI)CLASS900

EN 1092-1 (DIN) PN63
ASME B16.5(ANSI)CLASS1500

EN 1092-1 (DIN) PN100
ASME B16.5(ANSI)CLASS2500

EN 1092-1 (DIN) PN250
HE IS 10K

EN 1092-1 (DIN) PN400
HE IS 20K



Product application specific standards
System power supply

12~30V DC

Body material

Stainless steel 1.4301(304)

Stainless steel 1.4435 (316L)

Hastelloy C

Internal Impeller and Attachment Material

430F Stainless Steel

Stainless steel 1.4435 (316L)

Hastelloy C

(special option) VARIO

Customized with special parameters


The complete data of this selection table, please contact the sales staff or email to sales@kewill-auto.cn for complete samples.
Prev :FR55 Series Turbine Flowmeter
Next:FR80 Series Turbine Flowmeter (Bearing Type)
主站蜘蛛池模板: 91精品国产色综合久久不卡蜜 | 免费日韩毛片 | 91国自产精品中文字幕亚洲 | 日韩在线欧美高清一区 | 国产大学生真实在线播放 | 午夜精品久久久久久久99热 | 久久99国产精品久久99 | 国产精品国产亚洲精品看不卡 | 成人精品在线观看 | 国产精品免费一区二区区 | 日韩欧美国产高清 | 青春韩国无删减版电影在线观看 | 五月婷婷开心综合 | 午夜.dj高清在线观看免费4 | 精品中文字幕一区二区三区四区 | 99久久免费国内精品 | 国产精品久热 | 国产农村1级毛片 | 五月婷婷丁香网 | 欧美国产精品久久 | 免费xx视频| 亚洲人成77777在线观看网 | 国产成人精品综合在线观看 | 日韩日日日 | 国产成人精品一区二区三区 | 91精品国产91久久久久久最新 | 国产天堂网 | 亚洲精品国产字幕久久不卡 | 看国产一级片 | 成人欧美一区二区三区视频xxx | 第四色区| 久久久国产精品免费看 | 四虎影视成人 | 男性天堂网 | 国外免费精品视频在线观看 | 久久免费99精品久久久久久 | 国产一级电影在线观看 | 欧美成人免费草草影院 | 嫩草影院在线观看视频 | 久久国产精品免费 | 久久一级片 |